Tools You Need to Install a New Bath Tub
Tools You Need to Install a New Bath Tub
Blog Article
The article following next in relation to How to Install a Bathtub Yourself is pretty much enjoyable. Check it out for yourself and figure out what you think of it.
Mounting a bath tub isn't precisely rocket science, but it does require strong plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old tub with a new one is also a reasonably tough project. If the old tub is conveniently easily accessible, the job can move easily; if you need to open a wall to get rid of the old bathtub and place the brand-new tub, the task is a lot harder. In either situation, the project is within a residence handyman's skills, although you will require a helper to move out the old bathtub as well as set in the brand-new one. Ensure you have actually certified yourself for the work as well as are comfortable trying it. Instead of hiring a specialist to take over a halfway-completed task, it is much better to consider utilizing one before you start. Chances are you might need a specialist plumber to make tube links.
This article will certainly assist you install a brand-new bathtub in your washroom if you have currently purchased a brand-new tub and also don't require to alter the setup of your previous supply of water pipelines.
Your tools and also material list ought to consist of the following:
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you ought to do is disconnect the water system. After doing so, turn on the faucets to drain any kind of water remaining in the system. The procedure of removing the existing taps can be fairly problematic because of the limited gain access to that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the taps. Have a cloth all set for the continuing to be water that will certainly originate from the pipes. Once the supply pipelines have actually been removed, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from turning throughout this process. When the faucets have been eliminated, the holes in the bath/basin will have to be cleansed of any type of old securing compound.
Prior to going on to fit the new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly need a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, after that you will require minimizing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin making sure that the washing machines remain in place between the tap and the sink. Secure the tap in position with the supplier given backnut. As soon as the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The previous kind must be attached to the faucet finishes first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have been connected.
Installing the Bathtub
Using the two wooden boards under its feet, place the bathtub in the required position. The wooden boards are useful in uniformly spreading the weight of the tub over the area of the boards instead of focusing all the weight onto four small points.
The next goal is to ensure that the bath tub is leveled all round. This can be attained by examining the level and also readjusting the feet on the tub up until the spirit level checks out level.
To install taps, fit all-time low of the outermost adaptable faucet port to the suitable supply pipe by making a compression join; after that do the very same for the other tap.
Switch on the water as well as check all joints and brand-new pipework for leaks and tighten them if essential. Fill up the tub and additionally inspect the overflow outlet and also the normal electrical outlet for leakages.
Lastly, fix the bathroom paneling as defined in the maker's instruction manual. Tiling and also securing around the tub should wait till the bath tub has been used at the very least when as this will settle it right into its final position.
Planning for the Setup
Firstly, the supporting structure supplied with the bath must be fitted (if required) according to the maker's instructions. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is very important to ensure that if the tap includes a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps unit to avoid strain on the bath tub.
Fit the versatile faucet ports to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you use every one of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its final setting.
Tiling Around the Bath tub
In the area where the bath meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to fracture a rigid seal, triggering the water to pass through the wall in between the bath and the tiling, resulting in issues with wetness and also possible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your components and also fittings. They are sold in tubes and cartridges, as well as can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always fill up the tub with water prior to securing, to enable the activity experienced when the bathtub is in usage. The sealer can split rather very early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently readily available on the market. It is advisable to fit the tiles using water-resistant or water resistant adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a person who reads about A Step-by-Step Guide to Installing a Bathtub, I think sharing that piece was beneficial. If you please set aside a second to promote this content if you liked it. We take joy in reading our article about How to Install a Bathtub Yourself.
Details Here
Report this page